Non-Destructive Testing Services in Callaway, MD

Non-Destructive Testing Services in Callaway, MD

Callaway, MD API 650/ API 653

This is a worldwide recognized individual certification achieved through the American Petroleum Institute (API) testing program. Many individuals that hold this certifications are formal inspectors or welders. API 650 is the specification that deals with new construction of oil tanks. API 653 deals with the inspection, maintenance, repairs and alterations of storage tanks. This certification is highly sought after due to the volume of storage tanks located all over the United States holding petroleum products. These tanks require an external inspection every 5 years and an internal inspection every 10 years. Integrity Testlabs has performed many storage tank inspections. Radiographic inspections (RT) on the welding, Wet Fluorescent Magnetic Particle inspection on the floor plates and annular ring weld. Also Providing AUT scans, UT Thickness readings on the shell and UT crawler inspections on the outside of the tank.

Callaway, MD API 650/ API 653

ASME B31.1 in Callaway, MD

Created in the 1930s as a standard code for power piping. ASME B31.1 is a code that provides minimum requirements for safety and guidance for the design of new piping and the repair, modifications and replacement of existing piping. Covering fuel gas and oil systems as well as central and district heating, water and steam systems. ASME B31.1 covers water and steam piping found in all power generation plants throughout the United States. Integrity Testlabs can provided technicians on your next project or outage that have vast experience and knowledge of ASME B31.1 acceptance criteria.

ASME B31.1 in Callaway, MD

Callaway, MD Visual Testing (VT)

Probably the most important inspection technique and one we are gifted with is visual testing with our eyes. This is a very common, low cost, quick and effective way to inspect welding, equipment, and coatings. Visual testing is the most important tool for a Certified Welding Inspector (CWI), It’s a certification you can acquire through ASNT or with your company by ASNT TC 1A. Defects commonly found using visual inspection is excessive reinforcement, underfill, undercut, porosity, cold lap. If able to access the inside or root of the weld its possible to see lack of fusion, or incomplete penetration.

Callaway, MD Visual Testing (VT)
ANST Level I and Assistants

ANST Level I and Assistants

Becoming certified or learning about Nondestructive testing can be achieved in two ways. Enrolling in a school that provides a certificate or degree or getting hired on with a company with no knowledge of the industry and learning on the job. Typically 40hrs of radiation safety is the first step/certificate that is needed to get started. Once the Assistant has had some time in the industry the company will provide them with classroom training either in house, computer based or sending them to a course provided by a known 3rd party. When the Assistants meets the required OJT hours and classroom time. They will test with the company they are with by completing a specific, general and practical exams. When this is completed, they are now a Level II technician.

Eddy Current

Eddy Current

Eddy Current uses electromagnetic induction with alternating currents passed through a coil. The coil produces alternating magnetic field. Used extensively in the aircraft industry and manufacturing industry to look for surface and subsurface defects. Also used in the Nuclear and Petro chemical industry on heat exchanger tubing. When the surface is properly cleaned Eddy Current (ET) can be a fast and very effective Nondestructive inspection.

Callaway, MD Magnetic Particle Testing (MT)

If you’re looking for a very mobile, reliable and cost-effective method at finding surface and subsurface discontinuities. MT testing is the way to go on your ferrous material. When the magnetic field is disrupted by a break in the north and south poles the fine iron particles are attracted to the break in the magnetic field. Dry or wet inspections can be very useful with dry being the advantage when parts are to hot to use the wet method. ITL has many certified MT technicians to perform inspections on your welds or parts.

Callaway, MD Magnetic Particle Testing (MT)